• CAMERA

    CAMERA

    HD CAMERA MICROSCOPE

  • Microscope "Sorry Update website"

    Microscope "Sorry Update website"

    Sorry Not the work of some products Update website

  • Shaker New Product

    Shaker New Product

    Sorry Not the work of some products Update website

  • Autoclave New Product

    Autoclave New Product

    Sorry Not the work of some products Update website

  • fume hood New Product

    fume hood New Product

    Sorry Not the work of some products Update website

  • Stereo Microscope New Product

    Stereo Microscope New Product

    Sorry Not the work of some products Update website

 

INCUBATOR

 

 

To achieve the correct temperature distribution stable It was designated as a forced circulation method, Digital PID Controller Precise temperature control and setting is possible. Air -Warm has a uniform temperature distribution, so wrapped around the outside of the chamber, It is possible to fast temperature recovery after opening.

Validation support

 Operation qualification test Temperature compensation, real-time recorder and record the temperature as software Each position paper by the temperature test Test chamber temperature holding time in case of power failure Return temperature response test when the door is closed after opening 30 seconds

Feature

Sliding-Type was equipped with a shelf to shelf to take advantage of the convenient self-test. The precise temperature control is possible by Auto Tuning PID control. There is a temperature safety device to prevent operation was greater than the set temperature more stable. Using a forced circulation system improves the temperature distribution and the drying efficiency. 65 & lt; 0 & gt; C maximum temperature, the distribution & lt; 0 & gt; C 0.1 ± 0.1 & lt; 0 & gt; C to digital PID control close temperature control unit. Overheating protection device. Alarm, timer, was equipped with an auto-tuning, temperature compensation function. Chamber heated air is passed back in the middle, even by a fan motor It was achieved a good temperature distribution through a circular design, a faster drying rate. By heating the diffusion surface to the air of a uniform temperature around the fan's speed (Fan) ensuring high thermal efficiency and temperature uniformity. The heater and the fan motor is not running out of mechanical damage to the foreign object located on the back side of the chamber to the chamber bottom. All corners are rounded goby foreign objects do not leak into the outer chamber is easy to clean and easy maintenance. The shelf with adjustable height with 25mm interval is provided. Dual chamber is surrounded by a layer of air insulation effect of the insulation. If you open the door stops the operation of the heater and fan, and we consider your safety.

 

SPECIFICATION

MODEL
PH-I 100L
PH-I 150L
Dimension_IN(WxDxH)mm
500 x 400 x 500
500 x 500 x 600
Dimension_OUT(WxDxH)mm
635 x 670 x 760

http://www.cryste.co.kr/images/np_icon7.gif635 x 770 x 860

Chamber volume(L)
100
150
Heater
300w
600w
Power consumption
2.3A
2.7A
Plug type
 European 220 VAC STD plug
Electrical requirement 
220 VAC 50/60 Hz
Electrical

Electrical leakage breaker, with the use of fuses which are 
optimal to each part,overcurrent is shut- off.

Sensor
PT 100 Ω
Controller

Digital PID controller with timer, auto-tuning, 5 kinds of image print out

Temp.Heating type
Direct heating by stainless steel incolony heater
Temp.Range
1 Room ambient + 5 ℃ ~ 70 ℃
Temp.Accuracy
±0.1 ℃ at 37℃
Temp.Wait off timer
mm:ss 59 / hh:mm 99 / Continuous selectable
Temp.Heat up time to 37
Within 6 minutes 
Within 8 minutes
Material In
Stainless steel SUS-304
Material Out
Steel plate with powder coating
Safety device
Over heat protector.Heat protective barrier of controller box
Shelves Included
2
2
Option

RS-232c or 485 Interface port, software, com port cable, thermal printer

Branch: 14 Fawzy Soliman St., From El Haram St., Giza, Egypt P.O.Box: 127 Giza, Egypt Code:12515

Tel. Fax:+(202) 33943004 / Mobile: +2 / 01223415321-0111221096-01011811884

www.photoscience-co.com  / info@photoscience-co.com